Name:
Servo-controlled press
Description:
Servo-hydraulic and microprocessed press for concrete test with a maximum capacity of 200 ton (2MN). It works coupled to micro-computer, and with software that allows the performance of tests with constant rate of increase of load and maintenance of load, with high degree of automation and reporting. It includes an input to the strain gauge channel, thus allowing the use of a suitable strain gauge to determine the initial tangent modulus, secant modulus and tension-strain diagram according to ABNT NBR 8522, with fully programmed loading and automatic analysis of the results at the end of the test.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Servo-controlled press
Description:
Servo-hydraulic and microprocessed press for concrete test with a maximum capacity of 150 tons. It works coupled to micro-computer, and together with software that allows the performance of tests with constant rate of increase of load and maintenance of load, with high degree of automation and reporting. It includes an input to the strain gauge channel, thus allowing the use of a suitable strain gauge to determine the initial tangent modulus, secant modulus and strain-strain diagram according to ABNT NBR 8522, with fully programmed loading and automatic analysis of the results at the end of the test.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Fatigue test press
Description:
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Mortar MIxer
Description:
The planetary motion mortar mixer is used to make a mixture of cements and mortars. It has a motor with two speeds, tub and spade (stainless steel beater). Power supply: 220V - 60Hz. According to norms: NBR NM 52; NBR 7215.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Concrete Mixer
Description:
Concrete mixers are composed of: a drum, where the mortar components spin until the mixture is ready; the engine responsible for making the drum roll; the chassis, which have two wheels and provide support for the equipment to be transported; and the steering wheel, which is on the side and allows to move the concrete mixer to remove the mortar. This equipment mixes various materials, such as cement, stone, sand and water, to the desired consistency. Its operation takes place from an engine, which performs most of the work alone.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 7
Name:
Electric Ovens
Description:
Digital temperature controller with scale up to 1200 Degrees. Mufla with heating elements. Power 110 or 220 Volts. Ideal for research services, quality control in the laboratory
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Cutting machine with diamond disk for concrete and steel specimens
Description:
Cutting saw for concrete, bituminous materials, rocks or refractories. With motorized cooling, pedal for displacement of the disc and sliding table.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Extractor of stone specimens
Description:
The extractor is equipped with electric motor, allows the extraction of test specimens in pavements of asphaltic cement, asphalt and concrete. Its operation is characterized by being easy to operate, obtaining samples with ease. It has control of rotation with two speeds and mechanical transmission system using crowns and pinion
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Metallic reaction porch with a capacity of 200 Tf
Description:
Metal structure with a capacity of 200 ton for testing loads on structures (beams, slabs, etc.)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Transport porch with carriage and wheels
Description:
Metal structure with hoists and wheels for testing loads on structures (beams, slabs, etc.)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Hydraulic Cylinders
Description:
Hydraulic cylinders obtain the energy from a pressurized hydraulic fluid, which is typically some type of oil. The hydraulic cylinder consists basically of two parts: a cylinder and a movable piston connected to a rod. The hydraulic pressure acts on the piston, with a capacity of 100 tons, to produce linear motion.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 6
Name:
Hydraulic Cylinders
Description:
Hydraulic cylinders obtain the energy from a pressurized hydraulic fluid, which is typically some type of oil. The hydraulic cylinder consists basically of two parts: a cylinder and a movable piston connected to a rod. The hydraulic pressure acts on the piston, with a capacity of 200 tons, to produce linear motion.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Manual hydraulic Pump
Description:
It consists of an oil reservoir, manual pumping unit and external relief valve, an internally located safety valve, factory set at maximum pressure. This hand pump is used for typical high-pressure applications such as oil injection for breaking or removal of bearings, tensioning of hydraulic nuts, or in laboratory test applications (rupture, nuts and calibrations)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Vaccuum Pump
Description:
The vacuum pump is an equipment for the production of vacuum or the additional reduction of the pressure of an existing vacuum, it is used mainly in laboratory Soil.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Charge Cells
Description:
A charge cell is a transducer that converts the force into a measurable electrical output.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 4
Name:
Digital deflectometers
Description:
Deflectometer is an equipment used to measure small deformations in test specimens submitted to compression and / or bending.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 22
Name:
Resistive displacement transducers
Description:
A resistive transducer consists of a resistance with a movable contact. This equipment converts mechanical displacement into an electrical signal, by varying the length
Multiuser: Yes (x) No ( )
Pieces of Equipment: 8
Name:
High-precision displacement transducers
Description:
A resistive transducer consists of a resistance with a movable contact. This equipment converts mechanical displacement into an electrical signal, by varying the length.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Low-frequency accelerometers
Description:
The accelerometer is a device used to measure acceleration
Multiuser: Yes (x) No ( )
Pieces of Equipment: 20
Name:
Chloride penetration test system
Description:
Chloride penetration test system
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Data acquisition system with 7 Spider 8 modules
Description:
Data acquisition system with 7 Spider 8 modules
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Structural instrumentation systems based on fiber optic technology (Bragg networks)
Description:
Structural instrumentation systems based on fiber optic technology (Bragg networks)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Almemo multi-channel acquisition systems for various types of reading
Description:
Almemo multi-channel acquisition systems for various types of reading
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Vibration generation system (formed by shaker, DA-Digital Analog board)
Description:
Vibration generation system (formed by shaker, DA-Digital Analog board)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Pacometer
Description:
Electronic locator of concrete metal bars with digital display. The apparatus locates the bars and shows their diameter and length thickness of fittings up to 150mm away from the surface.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Ultrasound Device
Description:
Portable ultrasonic impulse measuring device with digital display for use in non-destructive test on concrete. This equipment is used in the indirect determination of uniformity, strength, cavities, cracks, damages caused by fire or freezing and modulus of elasticity.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Resistivity meter
Description:
The resistivity meter measures the resistance in a path between two points embedded in the ground. From the measured resistance, soil resistivity is calculated, which can be used directly to detect liquids, dimensioning of grounding for lightning rods, or, for cathodic protection projects in ducts.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Oversized Mufla
Description:
Mufla consists of a metal chamber with internal coating made of refractory material and equipped with resistances capable of raising the internal temperature to values above 1000 ° C
Multiuser: Yes (x) No ( )
Pieces of Equipment: 4
Name:
Microcomputers
Description:
A microcomputer is a computer characterized by the presence of a single microprocessor. With this equipment it is possible to manipulate several software required for engineering analysis
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Printers
Description:
Printer is an equipment that allows the printing of documents through paper and ink
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Optical extensometers
Description:
Extensometer is a transducer capable of measuring body deformations. Optical extensometers are applied in non-contact measurement, to measure the variation in length or change in width.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Electrical Resistance Extensometers
Description:
Extensometer is a transducer capable of measuring body deformations. Optical extensometers are applied in non-contact measurement, to measure the variation in length or change in width.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Piezometers
Description:
Apparatus for evaluating the compressibility or tension of liquids. It consists of a vertical tube, open on both sides, connected to the body of water
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Thermometers
Description:
The thermometer is a device used to measure temperature or temperature variations. It is an instrument composed of a substance that has a thermometric property, that is, a property that varies with temperature
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Precision Thermometers
Description:
The thermometer is a device used to measure temperature or temperature variations. It is an instrument composed of a substance that has a thermometric property, that is, a property that varies with temperature
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Analog Comparator Watches
Description:
The comparator watch is a comparison measuring instrument, with a scale and a pointer, connected by various mechanisms to a contact tip
Multiuser: Yes (x) No ( )
Pieces of Equipment: 16
Name:
Fork-lift
Description:
Forklift is a machine used to load and unload structural parts and goods on pallets
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Impedance Head
Description:
Impedance head made up of accelerometer and load cell coupled
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Vibrograph
Description:
The vibrator is an equipment capable of measuring cable displacements and thus providing an estimate of its useful life
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Anemometers
Description:
Anemometers are equipment that measures the velocity of the horizontal component of the wind, which is essential for the calculation of the energy forecasts.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Electronic Scale
Description:
Instrument used for mass measurements, which is composed of electronic elements such as load cells, integrated circuits, microprocessors etc.
Instrumento utilizado para medidas de massa, o qual é composto por elementos eletrônicos, tais como células de carga, circuitos integrados, microprocessadores etc
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Analitic Scale
Description:
Instrument mainly for the determination of masses with high precision and under controlled environmental conditions (temperature, humidity, etc.)
Multiuser: Yes (x) No ( )
Pieces of Equipment: 5
Name:
Large climate chamber
Description:
Climatic chamber used for thermal insulation with low temperature dissipation
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Carbonation chamber
Description:
Hermetically sealed chamber for the dissolution of carbon dioxide inside. This equipment is mainly used to evaluate the effect of carbonation on concrete
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Pull-out test equipment (with load control rate)
Description:
This system consists of a drill bit coupled to a 50 mm diameter saw-cup type drill, circular inserts with epoxy resin and trimming apparatus. This system has as purpose the determination of resistance of adhesion to the traction of mortars
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Machines for testing abrasion in concrete according to ASTM standard
Description:
The abrasion equipment allows to measure the wear suffered by the aggregate when subjected to a certain number of revolutions. The equipment is mainly equipped with an endless axle geared motor; a quick-release cover that ensures efficiency in the seal; a transmission system generated in the engagement of the push disk with the traction disk, which drives the drum in a counterclockwise direction. Accompany a tray with 12 (twelve) steel balls as recommended in the standard.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 3
Name:
Deionizer
Description:
Deionizer removes mineral salts producing chemically pure water with conductivity equivalent to bi-distilled water
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Desiccators
Description:
The desiccator is a laboratory glassware consisting of an enclosed container containing a drying agent called desiccant
Multiuser: Yes (x) No ( )
Pieces of Equipment: 3
Name:
Hothouse
Description:
Hothouse is composed of a thermally insulated box and a heat source. This equipment is intended to accumulate and contain the heat inside, thus maintaining a higher temperature inside it than around it
Multiuser: Yes (x) No ( )
Pieces of Equipment: 4
Name:
Concrete retraction testing equipment
Description:
Equipment used to evaluate the volume reduction occurring in concrete, even in the absence of mechanical stresses and temperature variations.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Sieve agitator with capacity up to 1kg
Description:
Bench top sieve agitator with vibration frequency controller. Power supply 110 / 220V - 50 / 60Hz. Accompanied with lid and bottom.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Sieve agitator with capacity up to 1kg
Description:
Sieve agitator for use with 50X50X10cm square screens, with capacity for 8 screens plus cover and bottom. Accompanied with lid and bottom. Power supply 110 / 220V
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Clipgages
Description:
Clipgages for concrete modulus test
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Digital caliper
Description:
Digital caliper is an instrument used to measure the distance between two symmetrically opposite sides of an object by reading the digital display.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Digital Sclerometer
Description:
The sclerometer is a portable measuring instrument that makes it possible to quickly assess the condition of a concrete structure for its strength. Its reading is carried out through the digital display.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Analog Sclerometer
Description:
The sclerometer is a portable measuring instrument that makes it possible to quickly assess the condition of a concrete structure for its strength
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Gas meters
Description:
Equipment responsible for carrying out the measurement of gases in an environment.
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Digital Torsion Machine
Description:
Equipment for the study of torsion tests, with possibility of twisting of test specimens until rupture. Torque measurement is performed through a charge cell and a microprocessor meter. The torsion angle is obtained through an angle transducer and a turn counter. The torque is applied manually using a flywheel and an industrial gear unit. The measurement is carried out with an instrumented auxiliary axis, whose deformation is compensated. The measurement can be read in Nm (Newton Metro) on a digital display.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Relative Humidity Meters
Description:
The moisture meter is a relative humidity measuring instrument in a given environment.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 2
Name:
Laboratory glassware
Description:
Laboratory glassware is glass or tempered glass instruments, so that the measurements are accurate and the container does not react with the substance contained in it
Multiuser: Yes (x) No ( )
Pieces of Equipment:
Name:
Equipment for “Water Bath”
Description:
Laboratory water bath equipment is intended to heat liquid or solid substances in which it cannot be exposed directly to the fire and needs to be heated, the water bath slowly and evenly heats by submerging the sample vessel in another liquid, usually water.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Centrifuge
Description:
The centrifuge consists of an electronic equipment containing test tubes inside it, which will be centrifuged for the purpose of rapid separation of liquid and solid elements
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Heating plate
Description:
The heating plate is an equipment in which it has a heated platform made of steel, whose function is to heat samples uniformly with constant temperature, and can be controlled digitally.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Conductivity Meter
Description:
The conductivity meter is a meter designed to measure electrical conductivity in liquids
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Sedimentation Cones
Description:
The sedimentation cone consists of a glassware in the conical format used to determine the natural sedimentation of suspended solids
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Destiller
Description:
The distiller is laboratory equipment responsible for the distillation of water for laboratory procedures.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Protein Distiller
Description:
Equipment used for protein distillation
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
COD reactor
Description:
The COD reactor consists of an aluminum block with capacity for several test tubes and a reference temperature probe. This equipment has the function of heating in dry media for small volumes
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Spectrophotometers
Description:
Spectrophotometer is an apparatus whose function is to measure and compare the amount of light absorbed by a given solution. This equipment is used to identify and determine the concentration of substances that absorb radiant energy in a solvent.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 4
Name:
Jar-test
Description:
The jar-test is an agitator which has the capacity for 3 tests and 1 liter. The shafts and stirring vanes are in stainless steel, with height adjustment, fluorescent lights at the base and electric speed control up to 200 rpm. This equipment is mainly used in tests during the treatment of water. Its function is to promote rapid and moderate agitation in the samples, facilitating the formation of flakes with the organic matter present in the analyzed water.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
pH meter
Description:
PH meter is a device used for pH measurement. It consists basically of an electrode and a potentiometer circuit
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1
Name:
Turbidimeter
Description:
Turbidimeter is an optical device that measures the decrease and the absorbance of the intensity of a light ray passing through a suspension. This equipment is used in the study of water analysis to verify its turbidity.
Multiuser: Yes (x) No ( )
Pieces of Equipment: 1